(approx) 1 Hour
Simple installation for anyone.
$1,001.99 (each)FREE Shipping
The TeraFlex RockGuard Outback Rear Bumper is for those of you that have a 2007 and up JK that are looking to upgrade to a very well built, very stout rear bumper, that's also going to be very simple. This is not over the top with features. Doesn't have a tire carrier. Doesn't have lights, high lift jack point. Doesn't have a lotta that stuff, but it is just a very simple, very well built strong bumper. This is going to install very easily onto your JK like most aftermarket bumpers. Definitely going to be a one out of three wrench bolt-on installation that will probably only take you around an hour or so. Now, like I said before, very simple bumper. It's gonna wrap around on the corners here giving you some protection from the sides. It has angles on the bottom of it to give you the best possible approach and departure angles. Of course, being a rear bumper, your departure angle is going to be what we're talking about here. It has a very deep cut out in the center here, so even if you are using a tub mounted tire carrier you can have up to a 39 inch tire and have plenty of clearance here. Again, nice deep V here. And, of course, you are going to have a couple of D-ring mounts, so you have your recovery points. And that's about it. Very, very simple, very well built rear bumper. Now this is also going to be one of the most expensive rear bumpers that we have that doesn't have a tire carrier. Now, a lot of that comes down to the quality, because you are getting, again, a very well built, very high quality bumper. But, for some of you, you might look at a lot of the other bumpers out there that are as simple as this one is and not be able to rationalize paying the additional price. And that's okay. This bumper's not gonna be for everybody. This is gonna be for those of you that know TeraFlex. That know the quality. That want that premium product and that have the budget for it. So for construction this is going to be, of course, a steel bumper. It's going to be covered in a black powder coat finish, which is gonna look really good, but it's also going to hold up very well and help protect this bumper against any sort of rust or corrosion. Like I said before, you do have the angles on the corners and the bottom to help you with your departure angles. You have those recovery points. And what makes these recovery points a little bit different is that generally they're gonna be welded through the bumper and they're gonna be directly onto the brackets that bolt onto the frame of the Jeep. So they are going to be very strong points. There's no denying that. These are a little bit different in the fact that they actually are the mounting hardware. This piece here goes all the way through. That's going to go on the inside of your frame rail, and there's a bracket that's on the back side the bumper here that goes on the outside of the frame rail and that sandwiches the frame between those two pieces. So this is going to be a really big, thick hunk of steel that's going to be directly bolted all the way through the frame and as one piece of metal sticks out through the bumper where your D-ring attaches. So you're going to have an even stronger attachment point, if that were even possible. So, again, its all about the quality here. It's all about simplicity. This is going to be a bumper that's definitely not a factory bumper but isn't an over the top aftermarket bumper with a lot of features. It's just clean, simple, and well built. So getting this installed is definitely a one outta three wrenches bolt-on installation, like I said before. About an hour's time. All you're going to need to do is first remove your factory bumper by removing the six fasteners that hold it in place. You're also going to have to remove a tow hook from your driver side frame rail if you have one installed. After that you can slide the bumper over top of the frame rails and slide the D-ring mounts, that solid piece of metal, into the inside of your frame rails, and then use the hardware to bolt through the bumper, through the frame, and into those D-ring mounts for a very solid connection. Those of you that know TeraFlex know that they make a very high quality part, and this is going to be no different. This premium bumper is going to command a premium price, and at around $900 it's definitely going to be one of the most expensive bumper options that we have, especially considering the fact this does not have a tire carrier and that it is just a bumper. But, you're getting something that's very high quality, that is going to hold up really well, that is a nice clean, simple design. And if you have the budget for it, I do think this is going to be a great option. If you are looking for a simple bumper that's a little bit less expensive, of course, we have those available as well. So, if you're looking for a very simple, very high quality rear bumper for your JK, this is an excellent option from TeraFlex, and you can find it right here at extremeterrain.com
Subscribe to our YouTube Channel
Features, Description, Reviews, Q&A, Specs & Installation
Construction. Engineered to provide extreme rock protection for your Wrangler, TeraFlex rear RockGuard bumper is made from durable steel with a black power coat finish. This bumper was designed with CAD software to provide a style that works with your Jeep and maximize protection from rocks and other obstacles. With its recessed spare tire well, this bumper can support up to a 39 inch spare tire. Installation is made simple with easy bolt-on hardware and mounting.
Application. Fits 2007-2018 Wrangler JK.
Freight Notes. Freight items can only be shipped within the continental 48 states, no expedited methods. What is freight shipping? Your Answers are Right Here!.
Fitment: 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 Details
CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
April 03, 2018
Well built. A little pricey for a bumper but get what you pay for. Very pleased with the whole purchase, shipment, packaging, quality, ect...Helpful (8)
July 17, 2017
TERAFLEX REAR BUMPER
This is a well made and solid bumper. The bumper is a little wider then most which I like. You can even stand on it. Easy install with everything lining up perfect. I really like how I was able to keep my original hitch too.Helpful (12)
December 25, 2016
Solid and stylish
This bumper is awesome. I installed it myself in a short amount of time with basic tools. It fit perfectly,very snug. It's heavy duty and stylish. I would highly recommend this bumper.Helpful (11)
May 07, 2016
No Problem Installation
Took about 30 minutes to remove the original JK Rubbermaid bumper. Had to buy an 1 1/8” socket. Installation time was about 45 minutes. Bumper is wide enough to stand on..Helpful (10)
May 02, 2016
Great fit and finish
Fits great and super easy to install. Not as heavy as advertised. Mine weighed in around 76lbs.Helpful (11)
(approx) 1 Hour
Simple installation for anyone.