Review & Install Video
I'm Ryan from extremeterrain.com, and this is my review and installation of the Fox 2.0 Performance Series IFP Shock, fitting all 2007 and up JKs. These shocks are available for one-and-a-half to three-and-a-half inches of lift and four to six inches of lift, and they're sold individually as front and rear so, make sure you get the shocks that you need for your build. Today we're gonna talk through the installation of these shocks which of course is a very, very simple one out of three wrench install. These will just bolt directly in place of your factory shocks, and you should be able to get these installed in about a half an hour per shock or less, but we'll talk more about the install in just a second. We're also gonna talk through the construction and a few of the features of these shocks.Fox is a really well-known name in the racing world and what they were able to do is take all of that R&D from building race vehicles for years and put it into these shocks that you can buy and put on your JK. You're going to get a really comfortable ride from a Fox shock as well as a lot of performance, and a shock that's going to hold up and take a beating both on road and off road. Now, Fox does have a couple different levels of their shocks. They're going to all ride similarly. However, they're going to be made out of different materials, so they are going to be different strengths and hold up to varying degrees. This is the Performance Series which is going to be a really high-quality shock, very, very well-built of high-quality materials. We'll talk a little bit more about that in a minute.Now, because you are getting such a quality piece and something that's going to ride so comfortably from Fox, you are going to pay a little bit more for their shocks especially this Performance Series because as I said, it is one of their higher end shocks. But, if you're looking for comfort level, dependability, durability, this is going to be a really nice option for you assuming you have the budget for it. These Performance Series shocks are made of a 60601 T6 aluminum and covered in a clear anodized finish, which is opposed to some of the lower-end Adventure or Evolution Series shocks from Fox, which are going to be a lesser grade aluminum material. Some of them are powder coated instead of clear anodized, and again, that is going to be a price difference for you.With any of these Fox shocks, you are going to get nitrile bushings on the bottom and the top which are going to be both quiet and last a good long time, and you are going to get a nitrogen charged shock. Now, there are hydraulic shocks, and there are nitro shocks. The nitrogen in a shock like this is there to eliminate any foaming and cavitation that you can get from working a shock very hard. A hydraulic shock doesn't have that protection, and if you are doing some high speed off roading or going over a lot of washboards, you're working that shock over and over, you can get some shock feed caused by that cavitation and that bubbling of the shock fluid. With a nitrogen-charged shock, you're not going to get that. Now, in general, a nitro shock will ride a little bit stiffer than a hydraulic shock. However, the ride quality really comes down to the valving, and that's what Fox does really well. Again, you're going to get a very comfortable ride, but also something that's very stable on the road at speed. Bolting an aftermarket shock on your Jeep is a very simple one out of three wrench install that you can get done in about a half an hour per shock. The most difficult part about installing an aftermarket set of shocks on your Jeep is removing that factory set if you have any rust, especially on the front upper shock nut. If you have some rust, that can definitely slow you down. That's an area that's very difficult to get to with a wrench. Oftentimes, if you have a lot of rust on there, it's easier to just put a big breaker bar on there and break the top of the shock off. It's
Superior Ride Quality. Take the trail head-on with the FOX 2.0 Performance Series IFP Front Shock for 4-6 inches of Lift. This front shock features race developed high flow pistons and is designed to provide increased ride quality on road as well as the stability and predictability you need for off road travel. Nitrogen charged and paired with internal floating piston technology and JM92 Advanced Suspension Fluid, this Jeep shock will maintain superior performance in a range of temperatures and conditions.
Rugged Construction. This Wrangler front shock features a 2.0" metal impacted 6061-T6 aluminum body construction for extreme strength. It is finished in a clear anodized finish for superior corrosion resistance and features black anodized CNC-machined 6061-T6 billet aluminum components. Providing superior functionality, this shock is fitted with a 5/8" hard chrome plated heat treated alloy steel shaft and makes use of quite nitrile rubber bushings for increased articulation during off road expeditions.
Bolt On. This FOX shock is a direct replacement for stock and most aftermarket lift kit shocks. It doesn't require any upgrades or modifications to your Wrangler for a quick and painless installation.
Application. The FOX 2.0 Performance Series IFP Front Shock is designed for use on 2007-2018 Jeep Wrangler JK and JK Unlimited models equipped with 4-6 inches of suspension lift. Sold individually, front only.
CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
- What's in the Box
- Installation Info
(approx) 30 Minutes
Simple installation for anyone.
- Tech Specs
- Will it fit my Wrangler?
- JK Rubicon 2 Door - 07, 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18
- JK Rubicon 4 Door - 07, 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18
- JK Wrangler 2 Door - 07, 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18
- JK Wrangler 4 Door - 07, 08, 09, 10, 11, 12, 13, 14, 15, 16, 17, 18