Talk to a Wrangler Sales Tech
1-877-870-8556
M-F 8:30A-11P, Sat-Sun 8:30A-9P
Logo Image
$20K Sweeps! 10 Chances to Win! Enter Daily >

DV8 Offroad LFS-7 Steel Mid Width Front Bumper with LED Lights (07-18 Jeep Wrangler JK)

Item J105067
ExtremeTerrain no longer carries the DV8 Offroad LFS-7 Steel Mid Width Front Bumper with LED Lights (07-18 Jeep Wrangler JK). Please check out Home for an updated selection.
Verify parts fit and get product recommendations.
Wrangler Sales Techs: Connect Now M-F 8:30A-11P, Sat-Sun 8:30A-9P
$0.00

    Product Videos

    Ryan: This DV8 Off-Road LFS-7 Steel Mid Width Front Bumper with LED lights is for those of you that have a 2007 to 2018 JK or 2018 JL, that are looking for an aftermarket front bumper that's going to provide a lot more features, some protection, and also a completely different look to the front of your Jeep. This is gonna be a pretty easy bumper to install. However, the lights do require some wiring to get them hooked up. So I'm gonna go with a two out of three wrenches for this installation, and we'll talk more about that in just a second. Now, this bumper is going to provide some additional features, like I mentioned before, some protection, some off-road-ready features and, of course, these lights. Now, these lights are going to be more of a marker light than they are something that's going to project and throw a lot of light out in front of your Jeep. So just know that, ahead of time, these aren't going to be the same as mounting a set of spot beam or flood beam aftermarket auxiliary lights on your Jeep. These are going to be a little bit more of a marker light, but that's okay. It adds to the style of this front bumper. Overall, I think that this is a fairly priced bumper for all of the features that are packed into it. As it says in the name, this is a mid-width front bumper. So this isn't going to be quite as wide as your factory front bumper or, of course, as wide as a full-width front bumper, but it's also not as stubby as a stubby front bumper. So generally, a stubby bumper will come out just past where the D-rings are on this. And this one, of course, is gonna have a little bit of a wider wing to it, making it that mid-width bumper. And that allows them to squeeze additional features into this, as well as offering a little bit more protection than a stubby bumper. Now, a lot of guys do want to run a stubby bumper because they don't want any interference issues between the big 37-inch tire and their bumper. With a mid-width, you may end up getting into some of that. So if you have a 37, just know that. If you're running 35's, you shouldn't have any issue with this bumper or with any other steel mid-width bumper. As far as features goes, again, steel bumper covered in a textured black powder coat finish to help it resist any sort of rust and corrosion. This does have two D-ring mounts, and it does come with the D-rings, which is a pretty nice feature. Right in the center here, you're going to have a winch mount that's going to hold any standard mounting winch and, of course, your fairlead mount here. And then you are going to have four LED lights that are going to be recessed right into this front bumper. And those are going to be a little bit more of a market light. Like I said before, you are going to have to wire those up. Up here, on top of the bumper, you're going to have this hoop and this does have two additional auxiliary light mounts on it. [inaudible 00:02:24] a light mount tab that will accept any regular single-post light mount, so you can add even additional lighting up on those tabs. This bumper is gonna run you $365. And there are some bumpers on the market that are going to look and function similar to this one that are a little bit less expensive. I do think you're getting a pretty high-quality build with this bumper. So if you like this look, if you like these functions. I do think this is going to be worth the cost. Now, somebody from the Install Team will show you how to get this installed on your Jeep. Man: The first thing you're gonna wanna do is unplug your factory fog lights. You're gonna wanna squeeze the tab on the back of your light and pull away from the vehicle. Now, you're gonna remove the eight 18-millimeter nuts that are located four on each side of the Jeep. Once you have your factory fog lights disconnected and the eight 18-millimeter nuts off the back of your bumper, you're gonna go ahead and pull it away from the Jeep. Now that you have your bumper off, you're gonna go ahead and remove the frame cover using a screwdriver or a removal tool. Now, we're ready to do the wiring portion of the fog lights on your bumper. As you can see, our fog light harness has already been cut into. So we're just gonna put the corresponding connectors on the bumper. Now, for you doing this at home, all you're gonna wanna do is cut your harness about 2 inches back from the plug and wire in whatever connector you would like to use. Now that you've made the appropriate electrical connections, you're ready to put your bumper on the Jeep. Using the provided hardware, you're gonna secure the three 19-millimeter nuts to the backside of the bumper, as well as a 19-millimeter bolt that goes on the inside of the frame. When installing your hardware, you're gonna wanna leave it a little loose until you have the bolt in on the inside of the frame. Now, you're gonna go ahead and put your bolt in directly above the nut we just installed on the inside of the frame. Once you have all four secured on one side of your Jeep, you're gonna go ahead and do the same thing on the other side, and then come back and tighten it all up. Once you have your six nuts and two bolts installed, you're gonna go ahead and tighten everything up. Once you have your bumper secured to the frame, you're gonna go ahead and connect your fog lights. Once you have them connected, you're gonna go ahead and wrap them in electrical tape, as well as tuck them up out of the way from any potential hazards. Now that we have our bumper mounted, as well as the lights wired up, that wraps up our review and install. You can check out more at extremeterrain.com.

    Product Information

    Features, Description, Reviews, Q&A, Specs & Installation

    Features

    • Standard Width Front Bumper
    • Heavy Duty 3/16" and 1/4" Cold Rolled Steel Construction
    • Premium Black Powder Coat Finish
    • Built-in Winch Plate, Rated up to 12,000 lbs.
    • Includes a Pair of D-Rings
    • Comes with 4 LED Lights
    • Backed by a One-Year Limited Manufactures Warranty
    • Fits All 2007-2018 Jeep Wrangler JK Models

    Description

    Made for Off-Road Adventures. Get your off-road machine prepared for your next aggressive trail adventure with the DV8 Offroad LFS-7 Steel Mid Width Front Bumper with LED Lights. It's the ideal accessory to make your vehicle ready for the brutal conditions of most challenging off-road trips. That's because it's made from some of the strongest materials and comes with durable D-Ring mounts and winch plates that are capable of withstanding incredible amounts of weight. With this on your Jeep, you can tackle the trail with complete confidence and peace of mind.

    Experience LED Brilliance. The DV8 LFS-7 bumper is also the ideal accessory for your nighttime trail adventures. That’s because it includes 4 powerful LED lights that produce an extremely bright lighting output without drawing too much power from your vehicle’s electrical system. This will help you light up the path much better compared to your Jeep's factory lights.

    Built to Last Long. This bumper is engineered to last for a long time with its heavy-duty 3/16" and 1/4" cold rolled steel and .120 wall steel tube construction. It’s extremely resistant to extreme bending and cracking and provides your vehicle with solid protection against logs, rocks, and other hard obstacles. Even the LED lights' housings are made to be tough thanks to the use of durable yet lightweight materials which protect the bulbs against vibration, moisture, and debris.

    Convenient Installation. Installing this front bumper is quick and easy with its bolt-on installation system. No additional vehicle modification is required to set this up on your Jeep.

    One-Year Limited Warranty. The manufacturer covers this product with a One-Year warranty against defects in materials and low-quality manufacturing.

    Application. The DV8 Offroad LFS-7 Steel Mid Width Front Bumper with LED Lights is designed to fit all 2007-2018 Jeep Wrangler JK models.

    Freight Notes. Freight items can only be shipped within the continental 48 states, no expedited methods. What is freight shipping? Your Answers are Right Here!.

    CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

    Installation & What's in the Box

    Installation Info

    What's in the Box

    • (1) Front Bumper
    • (2) Circular LED Lights
    • (2) Rectangular LED Lights
    • (1) Pair of D-rings
    • Hardware
    • Installation Guide

    Tech Specs

    4.3

    Customer Reviews (54)

      Questions & Answers

      10 More Questions

          Related Wrangler Categories