(approx) 30 Minutes
Simple installation for anyone.
$19.99 (each)FREE Shipping on orders over $75
Features, Description, Reviews, Q&A, Specs & Installation
Auxiliary with ease. If you're looking to add rocker switches to your dash, you can do so quickly and easily with the Daystar Switch Panel. It is a direct replacement for the OEM lower dash panel.
Features. This Daystar lower switch panel accommodates 1-4 rocker style switches for you auxiliary lights or accessories. It Installation is quick and painless with no extra cutting or modification required, leaving you more time on the road instead of in the garage.
Application. This Daystar switch panel is designed for 2007-2010 Jeep Wrangler JK models. Switches sold separately.
Fitment: 2007 2008 2009 2010 Details
CA Residents: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
January 15, 2020
Works as advertised.
Fits as it should 2010 automatic. Directons were easy enough.Helpful (0)
October 19, 2019
Good fit in the dash and Awsome functionality
Install was easy and function is awesome but with the standard tranny it bumps the switches in 1st and 3rd. I put my backup light switch where the shifter hits so it turns off my back lights when I shift in first. All good! LolHelpful (0)
July 19, 2019
Bought this for our 2007 4 door jk wrangler so I could put a light bar switch in it, came with instructions even though it was as simple as using a razor blade to cut out the pre marked spot for the switch and putting the clips on off the stock panel.Helpful (0)
February 16, 2019
Struggling with gear shift boot
It fits and put the switches where I was trying to put them. However, i dont recommend this panel or this location for your switches. The 1st slot on the left works great, but the switch in the 2nd slot keeps getting switch off by my factory shifter boot. I had to push the boot down and zip tie it to keep my switches on, but that gives you resistance when shifting into 1st, 3rd and 5th. If you dont intend to use these switches very often, it might work fine for you. Happy jeepin'Helpful (3)
December 29, 2018
It works good.
I have a wrangler with a manual shifter and although it says it will work. The instructions say just push down the rubber boot. But it continues to slide back up as you shift. It actually will flip the switch on the two right switches to off just by normal shifting. That being said it’s a quality part that actually fits and looks great in my Jeep. Simple to install as welll. I would buy it again but the could have made it slightly thinner to accommodate the shifting.Helpful (4)
June 20, 2018
easy install took me less then a 1/2 hr. wish it came with the switches or had the optionHelpful (10)
May 23, 2018
Modify Switch Panel for JK to TJ
I could not find a switch panel for my 2001 Jeep Wrangler Sport. So l ordered a this dash switch panel and modified it by trimming cutting to fit next to ash tray on dash. Works perfect.Helpful (10)
November 10, 2016
The switch panel was super easy to put in. Just pop out the old one, attach your new switches to the Panel, and put it back in place. Great look too!Helpful (12)
October 23, 2016
I like this switch panel. It works fine for the first switch I put in, a heated seat. Next will probably be a light bar switch.Helpful (11)
August 19, 2016
It sure is nice to buy aftermarket products that actually meet you expectations! Fits as it should, very easy to cut out for switches and looks great in the vehicle! I do this work for a living and I will be buying more of these for sure!Helpful (12)
will this switch panel work with a 2007 jeep jk manual transmission or will ot get in the way of when im shifting?
Hello, this switch panel will work in a 2007 JK Manual Transmission.
does this have rocker switch options? looking front/rear locker, compressor/air
The Daystar Dash Switch Panel will come as just the panel with no switches installed. This uses standard style switches, which we have a full assortment of at the link below: https://www.extremeterrain.com/wrangler-jeep-jk-switches.html#shop-by2
Do the rugged ridge rocker switches work with this panel?
The Rugged Ridge Rocker switch's haven't been tested and verified for fitment with the Daystar Dash Switch Panel but there is the possibility they may fit since you need to cut out the slots on the panel for the switches. I recommend using the Daystar Rocker Switch's that will fit with this switch panel. The blue switch can be found here : https://www.extremeterrain.com/daystar-rocker-switch-blue-ku80011.html We do also carry the 3 other colors as well.
Does this include the switches themselves? Is it just a piece that you can attach switches to that are sold separately, or are there switches included in the box?
Hello, unfortunately the Daystar Dash Switch Panel - Lower (07-10 Wrangler JK) does not include the switches. You can the Daystar Rocker Switch - Red Light (87-17 Wrangler YJ, TJ, & JK) (other colors available) and you can find it here: http://www.extremeterrain.com/daystar-rocker-switch-red-ku80014.html
(approx) 30 Minutes
Simple installation for anyone.
What's in the Box