- (2) Mounting Brackets
Free Shipping on Orders Over $75. Details
$49.99FREE Shipping on orders over $75
RedRock 4x4 Dual Vertical Windshield LED Light Mount Brackets - Textured Black (07-18 Wrangler JK)
I'm Ryan from ExtremeTerrain.com, and this is my review and installation of the RedRock 4x4 Dual Windshield LED Light Mount Bracket, fitting all 2007 and up JKs. Today we're gonna walk through the installation of this bracket, which is a very simple one out of three wrenches, because this is designed to bolt directly on to the Jeep, without any permanent modification, using your factory windshield hinge hardware. We're also going to talk about the construction and a few other features of these brackets. A bracket like this is gonna be for those of you who want to mount a light on your A-pillar, but not just one light, two on either side. Now, having two lights on either side does give you a lot of flexibility. You can have two different beam patterns, one's a flood, one's a spot. You can have them different colors. One can be white, and one can be yellow, which is a look I really like. You can have them switched independently, of course. You can just have a lot of different functionality, and a lot of different features, if you decide to run two sets of lights on your A-pillar. And these brackets will allow you to do that. These brackets are a little different from some of the other ones out there on the market. These are going to hold your lights in a way that you only have a horizontal point of adjustment. You're not going to be able to aim them left, right, only up and down, which does limit you a little bit with your options. If you wanted to have a set of floodlights that are pointed out toward the gutters, and then have a set of spotlights pointed straightforward, you're not going to be able to do that with these brackets. There are some other dual light mount brackets that do use a more traditional single place light mount that will still give that up-down, and side to side adjustment. This kit is not one of them. Although this kit is also going to be less expensive than those other ones. So if you're not going to use that left-right adjustment, this kit is going to be a perfectly fine option. As far as construction goes, these are these are steel brackets covered in a textured black powder coat finish. They're maybe not quite as beefy or as strong as some of the other ones on the market. They do have a little bit of a flex to them. However, they're just a light mount bracket. They don't need to hold a lot of weight, and the way that these are designed, you actually put the light in between the bracket, and the light becomes part of the structure of the mount. So everything will certainly be firmed up once you mount your lights in these brackets. They, again, are designed to bolt on to the Jeep without any major modification, using all your factory hardware and your factory mounting locations. So all in all, they're a simple part, they look good, and they'll save you money, over those top quality mounts on the market. To get these installed is a very simple one out of three-wrench installation. All you'll need to do is to remove the two windshield hinge cover bolts from the front of your windshield hinges, put your bracket in place, and replace those screws. Now, this doesn't come with any sort of gasket material to go between your painted surface of your windshield hinges, and your brackets. So you might want to fab something up, cut a piece of rubber to put it behind there, or put some silicon on the back of this. Let it set up before installing it, if that's something that you are concerned about. All in all, the installation of this won't take you more than a half an hour, and you won't need any specialty tools, although you will need a large torx bit. I'm sure if you've done any work on your Jeep, you have a big torx bit set around, but if this is one of your first mods, you are gonna need to pick that up. As I said, this is going to be a little less expensive than some of those top-tier mounts on the market. A dual A-pillar mount from, say, Rigid is going to be significantly more expensive than this one. It may have some additional features as far as how you can aim it. However, if you're just looking for a simple light mount that's going to allow you to mount four lights facing forward, this will certainly save you some money. So, if you're looking to mount four lights on your A-pillars, two on either side to allow you to have different beam patterns, different colors, or just have the lights switch independently, this is going to be an inexpensive way of getting those lights mounted up. So that's my review of the RedRock 4x4 Dual Windshield LED Light Mount Bracket, fitting all 2007 and up JKs, that you can find right here at ExtremeTerrain.com.
Fitment: 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 Details
Installation Time: (approx) 30 Minutes
Difficulty Level:Simple installation for anyone
No questions about this product yet.Ask the First Question
June 05, 2017
Great Light set up!
Great mount that is extremely unique yet functionble! Allows for a lot of light output with out slapping light bars everywhere on your Jeep! Love this product!
Bang for your Buck 5
January 01, 2017
Better designs out there
I was given these as a gift, should have specified what exactly I wanted haha. They do a good job of mounting the lights and are solid but they also take up a fair chunk or your windshield. Others put the lights further to the side but these put them right in your face
Bang for your Buck 2