ExtremeTerrain is proud to offer FREE SHIPPING on any order over $75!
Free 2-3 Day Delivery on most items, see Product Page for details.
Free Shipping Offers are for Standard Ground Delivery Service and are only valid for shipping addresses within the 48 contiguous United States. Truck freight and oversize charges still apply unless otherwise noted, and can only be shipped to the lower 48 States. Rough Country items are not included in Free Shipping offers. Tires and Wheel and Tire Kits do not qualify for free shipping.
Shipping to Alaska and Hawaii will require an additional charge.
Merideth: If you want some aggressive exhaust notes and more clearance off-road for your 2016 or newer 3.5-liter Tacoma, this Flowmaster FlowFX Extreme Single Turn Down exhaust system will be the kit to check out.Now, right off the bat, when it comes to sound, this will be higher up at a four out of five in the loudness meter, one being completely stock, five being wake the neighbors, loud. Now this will do a great job at deepening the tone of the exhaust and also increasing the volume, creating a more aggressive presence to the truck without too much interior annoyance or drone, making it pretty comfortable.Now as far as performance, this will also give you some minor gains, getting you some better throttle response, and also some better efficiency, while also offering a lot of clearance compared to other systems. Great if you're taking your truck off-road.Now, this kit will be made of 3-inch diameter mandrel bent 409 stainless steel, offering consistent and direct airflow, as well as some pretty good rust resistance. Now the tip will also keep the same features of the rest of the exhaust, with a 3-inch turn-down style tip, as well as a brushed finish.Now, again, this will be a turn-down style exhaust, so not only will you not see this, but it's also gonna stay out of the way of any obstacles if you're taking your truck off-road, minimizing any damage compared to a side exit or a rear exit system. This will also be a direct bolt-on application and come with everything you need in order to make this a straightforward install.Getting into prize, this will be on the more affordable side, mainly because of the style of exhaust at roughly $350. Now with that price, you're getting a solid build with the rust-resistant 409, some really aggressive notes, and decent amount of volume, as well as a high clearance system.Now others available on the page may just be set up a bit differently with a 304 stainless and may cost you a little bit more being on the higher quality side compared to 409, a side exit, or a dual exit configuration, or even a little less volume than this choice. Now, overall, I think if you really don't care for looks and you just want a good-sounding and well-made system at an affordable price, then this is gonna be it.Now, install will be two out of three wrenches on the difficulty meter, taking you about two hours to get the job done, and I wouldn't be surprised if you get it done a little bit sooner with some basic hand tools. However, that is gonna wrap it up for my review. Let's go ahead and head over to the shop, where we can show you a detailed breakdown of the install right now.Man: Tools required for this install include an impact gun, a can of penetrating lubricant, an exhaust hanger remover tool, a tape measure, 14 and 15-millimeter socket, a marker, as well as a saw, a grinder, and pole jacks or a jack stand.What's up, guys? Today, I'm gonna be showing you how to install an exhaust on our Tacoma, so let's get started. So, our first step is gonna be to disconnect our hanger on our tailpipe, as well as our frontmost hanger behind the flange. We're gonna leave the two hangers connected behind the muffler until we disconnect our flange and we're ready to fully remove our exhaust.So, I've gone ahead and sprayed our hanger down with some penetrating lubricant, just to make it a little bit easier to slide off. And then I'm gonna get in there with an exhaust hanger remover tool to slide this out. So, now coming to the front side of our muffler right behind our flange, we can remove our second hanger. I went ahead and did the same thing, sprayed it down with some penetrating lubricant, and then we can pop that out.So, now with our two hangers removed, we can attack our flange. So, these are gonna be two 14-millimeter bolts, so I'll get a 14-millimeter socket on an impact gun and get these off. So, now with our flange unbolted, we can hit our last two hangers that are right behind the muffler. So, I'll get in there with our exhaust hanger remover tool. So, now I've thrown a pole jack underneath our muffler just to hold the exhaust into place while we remove our last exhaust hanger. Once again, I'll get behind that with our exhaust remover tool and pop that out. So, now we can start to slowly lower our pole jack and move the exhaust out towards the front of the truck.So, now with our stock exhaust removed, before we can install our new one, we're gonna have to make some cuts. Now, this is only for if you have the 128-inch wheelbase. If you have the 141-inch wheelbase, you won't have to cut this pipe. Since we have the 128, we're gonna have to cut 13 inches off of our pipe. So, we'll grab a tape measure, lay it down, mark off at 13 inches, and we'll take it over to the saw and make our cut. So, we'll make our mark at 13 inches, and I'll meet you over at the saw to make our cut.So, now I've got our pipe lined up with our cut, so we can go ahead and make our cut, clean up our edges, and then get this installed on our truck. So, now with our cut made, we can come over to our grinder to clean up our edges. So, now with our edges cleaned up, we can take this back and get it on the truck.So, now we can go ahead and install our new front pipe. We're gonna be reusing our factory hardware, those 14-millimeter bolts. So, line it up and get our bolts started. Now we can take a 14-millimeter socket on the impact gun and tighten these bolts down. So, now we can take our 3-inch clamp with the hanger and we're gonna slide it into our hanger here and over our front pipe. So, now we can install our muffler. So, we're gonna slide through our two hangers first, and then we're gonna make our connection to our front pipe. So, now we can slide our clamp into position, and then we'll take a 15-millimeter socket on an impact gun to snug that down.So, that'll wrap up this review and install of the Flowmaster FlowFX Extreme Single Exhaust System with Turn Down for your 2016 to current 3.5-liter Tacoma. Thank you for watching. And remember, for all things Tacoma, keep it right here at extremeterrain.com.
Delivers a Formidable Sound. Add an even more formidable character to your truck than before with this Flowmaster FlowFX Extreme Single Exhaust System; Turn Down. It is equipped with a muffler and pipes that are engineered to provide unrestricted exhaust flow. And with its smooth design, this exhaust system lets your truck roar with an intimidating sound that is guaranteed to turn heads anywhere you drive.
Remarkable Power and Torque. This Exhaust System equips your truck with high-quality, mandrel-bent pipes. They feature a smooth and free-flow design that accelerates exhaust flow, giving your truck increased power, torque, and efficiency.
Heavy-Duty Construction. This Flowmaster FlowFX Exhaust System is designed to complement your truck’s rugged character. It is manufactured using a 3-inch-diameter, 409 stainless steel that makes it withstand punishing diving conditions, making it perfect for a variety of adventures.
Premium-Level Brushed Tip. This Exhaust System comes with a turned-down tip. It features a brushed finish that delivers excellent protection against corrosion while also giving a more eye-catching look to your vehicle.
Trouble-Free Installation. The design of this Exhaust System allows for fast and simple installation. It comes with all the required installation hardware and mounts to factory hanger points so you can set it up quickly without modifications to your truck.
Backed by a Limited Lifetime Warranty. To assure quality, Holley guarantees to the original purchaser that this Flowmaster FlowFX Exhaust System is free from material or manufacturing defects for the life of the vehicle on which it is originally installed from starting from the original date of retail purchase. Other conditions apply. Please refer to the manufacturer’s website for details.
Application. This Flowmaster FlowFX Extreme Single Exhaust System; Turn Down is designed for all 2016 to 2023 3.5L Toyota Tacoma models.
WARNING: Cancer and Reproductive Harm - 
