Talk to a Wrangler Sales Tech
1-877-870-8556
M-F 8:30A-11P, Sat-Sun 8:30A-9P
Logo Image
$20K Sweeps! 10 Chances to Win! Enter Daily >

How to Install a Barricade Replacement Soft Top - Black Diamond on your 1997 - 2006 Jeep Wrangler TJ

Tools Required
  • Shoe Horn
  • Safety Glasses
  • Razor Knife
  • Phillips Screwdriver

WARNING!

This product is designed to enhance the appearance of the vehicle and to shield the occupants from ordinary weather conditions. Do not rely in any way on the components of this product to contain occupants within the vehicle, or to protect against injury or death in the event of an accident. This top will not protect the occupants from falling objects. Never operate vehicle in excess of manufacture's specifications. 

Wear Seat Belts At All Times

Read and follow, precisely, all installation instructions provided when installing top. Failure to do so may result in a poor fitting top and could place occupants of the vehicle in a potentially dangerous situation. After installing or reinstalling the top, check to make sure it has been properly installaed before driving.

Parts List

Fabric TopQty - 1
Quarter Window, RightQty - 1
Quarter Window, LeftQty - 1
Rear WindowQty - 1

Installation Tips

Before you begin to install the new top, read all instructions thoroughly. Below are a few tips to make this installation easier. After completing the installation, keep these instructions for further reference.

For a Smooth Fit:

For ease in installation, the top should be installed at a temperature above 72F. Below this temperature, the fabric may contract an inch or more, making it hard to fit to the vehicle. It is normal for the fabric to contract and wrinkle when stored in the shipping carton. Within a few days of the installation, the fabric will relax and the wrinkles will disappear.

Removing the Old Top - CAUTION

Safety glasses should be worn at all times while installing this product.

Step 1:

Remove the quarter windows and rear window. Remove the metal tailgate bar from the bottom of the rear window and set to the side. It will be reused.

Release the plastic strips sewn to the top above the doors. Pull down and out to slip the plastic out of the channel.


Step 2:

Release the latch that secures the header to the windshield. Pull up on the lever and then down and out to release the hook from the slot in the windshield frame.


Step 3:

Release the rear corners of the top. Pull gently down and then out to release the plastic strip from the retainer on the vehicle.


Step 4:

Unfasten the flap around the middle bow.


Step 5:

Unsnap the fabric from the rear bow and allow the bow to drop onto the tailgate.


Manufacturing Note:

Due to recent header assembly modifications by Daimler Chrysler, the plastic strips on the windshield header may have 8 screw locations instead of 14. Both attachment number of screws will securely fasten the header and perform as intended.


Step 6:

Collapse the bow assembly down onto the tailgate. With the bow assembly laying on the tailgate, remove the screws that fasten to the corners of the header. Set screws aside for use later. They are reused for the installation of the new top.


Step 7:

Flip the top fabric back over into the rear of the vehicle (so that the fabric lays backing side up) to expose the plastic strip along the edge of the fabric. Remove the eight or fourteen screws that secure the fabric to the header, setting the screws aside for use in the installation of the new top. Then remove the old top fabric from the vehicle.


Installing the New Top


Step 1:

IMPORTANT! If you have a 1997 vehicle with a slip-on plastic extrusion on the door surround, it must be removed. Pull down on the extrusion to work it loose.

Step 2:

In order to install the top fabric, make sure that the center and rear bows are in the folded down position on the rear of the vehicle.

Lay the top fabric, backing side up, in the rear of the vehicle with the plastic strip facing up and aligned with the front edge of the header. Locate the round hole that marks the center of the plastic strip (all other holes are slotted). Install a screw in the round hole to secure the fabric to the header as well as to center the top. Then proceed to install screws in the remaining seven or thirteen holes along the front of the header.


Step 3:

Flip the fabric over so that it wraps around the header and drape the top fabric over the tailgate. Raise the header slightly and work the pockets in the fabric over the corners of the header. Install an oval head screw in each corner to secure the fabric to the header.


Step 4:

Raise the header and bow assembly towards the windshield and into position. Inside the top, snap the fabric to the rear bow (total of six snaps).


Step 5:

Make sure that the center bow is centered in the hook and loop flap inside the top. Do not fasten the flap at this time.

Pull down gently on the rear bow and work the plastic sewn to the rear corner of the top into the retainer on the vehicle.


Step 6:

Close the header latches to secure the front of the top to the windshield. Catch the hook in the slot in the windshield frame and then close the lever over it so that it lays flat against the windshield frame.


Step 7:

Wrap and fasten the hook and loop on the two flaps inside the top around the center bow.


Step 8:

Locate the left and right quarter window panels and orient them with the zipper slider about 10" - 12" along the top.


Step 9:

Roll the plastic along the front of the panel into the channel of the door surround on the vehicle. 


Step 10:

Locate the plastic strip sewn to each side of the top, above each door. Slip the strips into the channel in the door surround above the door opening.


Step 11:

Close the zipper on the quarter panels the rest of the way to the lower rear corner of the panel. Start at the rear and roll the plastic along the bottom of the panel into the retainer on the vehicle. Then fasten the hook and loop strips along the rear of the panel to the top.


Step 12:

Remove the rear window from the box and lay it flat with the backing side up. Locate the tailgate bar set aside in step one. The bar has a "C " shaped channel, when viewed from the end. Orient the bar with the round seal down and slide the "C " channel on the retainer onto the tubed strip sewn to the backing side of the rear window.


Step 13:

Insert the tailgate bar into the mounts on each side of the tailgate opening with the vinyl side of the rear window towards the outside of the vehicle. 

Step 14:

To start the zipper, pull the two sliders as far down as possible on the driver's side of the window in order to catch the sliders to the pin.

Once the zipper is caught, start the top slider 1/2". Then hold up the top of the window with one hand and close the zipper with the other. The zipper in sandwiched between layers of fabric in the corners so be careful not to catch extra fabric in the zipper. Close zipper.

Make sure that the tailgate is centered and is securely in the mounts . Then tuck the flaps on the rear window under the top fabric. 


Folding The Top Down

Step 1:

Remove the quarter panels and rear window curtain and store them carefully.


Step 2:

Release the front of the top from the windshield. Raise the front of the deck and collapse the rear bows, tucking the two plastic strips above the door opening and the stay pad on the rear bow inside of the bows. Wrap the fabric around the bows, then tuck the rear legs of the top under the bows.